1998 Carroll 40' _{(12.19 m)} Farr 40 One Design

RASCAL

Purchased in 2016 with plan to completely rebuild the hull and deck

The rebuild has resulted in a very dry, stiff hull and deck, benefitting performance in all conditions

Minor modifications made to the standard Farr 40 design spec:

- 4" increase in waterline length resulting from straightening the stem to plumb, from raked

- Increased chamfer on sheerline for enhanced crew comfort when hiking legs out

The interior was freshened with a new paint job.

The standard interior layout lends itself equally well to both day racing and distance racing

Sails include:

• delivery/daysailing dacron mainsail
• 3 x delivery/daysailing jibs
• delivery/daysailing Code 0
• 3 x racing conditioning spinnakers

The rebuild/refit resulted in RASCAL being virtually a new boat - see details below

REBUILD & REFIT

> Hull balsa core completely replaced from bow to stern

> Bow modified to plumb from raked with 4" increase in waterline length* - for aesthetic value only

> Hull then faired and longboarded

> All deck balsa core replaced with high density fibreboard

> Added gunwhale radius molded in for greater crew comfort sitting on the rail legs out*

> Hull and deck painted with Awlgrip

> Bottom sprayed with 7 coats of VC Offshore

> Interior repainted with Petit Eazypoxy

> V-berth floorboards fabricated and installed

* these changes make RASCAL ineligible for one-design racing

> Running rigging replaced with Dyneema ropes to class specs

> Standing rod rigging entirely replaced - Offshore Spars, MI

> Lifelines replaced with ss 1x19 wire - Abbott Boatworks, ON

> Bow and stern pulpits powder coated - Whitewater Marine, MI

> All winches refurbished

> Majority of Harken blocks replaced

> New steering wheel - 2024

> New i-series Raymarine instruments - 2019

> New autopilot - Garmin Octopus model 1012 - wired, ready to install

> Engine stripped down and rebuilt with new injectors, new waterpump, new water separator, exhaust and all new hoses, clamps and gaskets

The photo gallery includes lots of photos taken at various times during the rebuild - a truly extensive, comprehensive project

ORIGINAL CARROLL MARINE SPECS & EQUIPMENT

Construction

Epoxy/E-glass/Foam/Balsa composite

We pre-preg, post cured in oven

Keel & mast support structure - aluminum grid

Keel: cast iron fin, lead bulb, epoxy coated

Mechanical

Yanmar diesel - 3GMSD30 Sail drive

2-blade folding geared prop

Fuel tank - 19.8 USG, aluminum

Fuel filter and water separator

Single lever throttle and gear control

Fuel gauge

Muffler/exhaust system

Electrical

12V DC distribution panel

Battery condition meter

Circuit breakers of appropriate amperage

Main battery switch

2 x 105Ahr batteries

80A alternator on engine

ORC approved nav lights

Red & white dome lights for general interior lighting

Halogen reading lights

Plumbing & Stove

2 x 21 USG water tanks

Cold pressure water system

Galley sink with overboard drain

2 x manual bilge pumps; cockpit and interior

Manual marine toilet with holding tank and pumpout

Fresh water fill below deck

Ice box

Stove - custom 3-burner butane

Deck Hardware

Winches:

• Primaries; 2 x Harken 48 3-speed, aluminum
• Halyard; 2 x Harken 44ST 2-speed, aluminum
• Mainsheet; 2 x Harken 44ST 2-speed, aluminum

Hydraulic backstay adjustor

Pulpits - ss custom bow & stern rails with nav lights

Stanchions - 6 x tapered, 4 with braces

Stanchion bases - custom flush fit

Lifelines - upper and lower, 1 x 19 ss

5 x rope clutches for halyards and spin pole lift

Jib tracks, port & stbd, fully adjustable with underdeck control lines

10:1 barberhauler system

Cunningham, led aft to main trimmer

Outhaul, led aft to main trimmer

'German' mainsheet system, led under deck

Spinnaker foreguy

Foredeck hatch, 24" dia, alloy

2 x cockpit opening ports, 5" x 12"

Steering

Carbon rudder stock with epoxy/carbon/e-glass blade

Upper & lower roller bearings

Optional wheel steering system - new wheel 2024

(std steering - custom alloy tiller with extension)

Spars & Rigging

I = 53.15' J = 15.45' SPL = 17.06' ISP = 60.04'

P = 54.79' E = 19.36'

Sail area = 1,109 sq ft

Custom carbon rig:

• 2 sets swept spreaders
• integrally molded deck collar
• roller bearing spin pole track

Aluminum boom with outhaul and 2 reefs

Rigid vang with tails led aft port & stbd

Carbon spin pole

Discontinuous ss rod standing rigging

Kevlar permanent backstay with hydraulic adjustor

Tuff Luff forestay foil

Running rigging:

• mainsail halyard
• 3 x forward halyards
• mainsheet
• outhaul
• cunningham
• 2 x traveller control lines
• 2 x jib sheets
• 2 x Jib in-haul lines
• 2 x jib car puller lines
• 2 x spin sheets
• 2 x spin afterguys
• 2:1 foreguy
• backstay strop
• 2 x spin twing lines

Miscellaneous Standard Equipment/Features

Exterior finish: light colour gelcoat on topsides and deck

double bootstripe

clear epoxy on bottom, ready to sand and paint

Foils epoxy coated and faired to template

Interior finished in matte white paint

4 x fixed berths with 4" cushions

Fabric covers on hanging lockers

Disclaimer

The company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct his agents, or his surveyors, to investigate such details as the buyer desires validated. This vessel is offered subject to prior sale, price change or withdrawal without notice.

Listing MLS by Yachtr.com