1989 Bruce Roberts 44' (13.41 m) Custom 44 Bruce Roberts Design Built by Topper Herman co Fernandina Beach Fl
Jacksonville, Florida, United States
Locally built Bruce Roberts 44 custom steel cutter with Perkins diesel, cutter rig, solar, wind generation, watermaker, air conditioning, large engine room and true offshore-liveaboard capability.
Flag of Registry: United States
Port of Registry: JACKSONVILLE fl
- Cutter / Sloop
- Sail
- Used
- Diesel
- Steel Hull
- HIN/IMO: TPR44001G989
| FEATURES: |
|---|
| Topper Hermanson Boat custom build from Fernandina Beach, Florida |
| Perkins 236 85 HP diesel with Borg Warner 2:1 transmission |
| Cutter sail plan with Profurl furler and extensive sail inventory |
| Solar, wind generation, Xantrex inverter/charger and Sea Recovery watermaker |
| Two-stateroom, two-head cruising layout with large aft master and workshop |
| Notable Upgrades: Lexan window resealing; toe-rail/localized steel welding; shaft packing renewed; electrical-panel and smart-control improvements; continued restoration after the 2023 survey. |
| Date Listed: 08/01/2026 |
Custom Steel Bluewater Cruiser
$ 88,000 USD
€ 76,484 Euros
$ 123,583 CAD
£ 65,554 GBP
Description
Ravenwing is a one-off 44-foot custom steel cruising yacht built in July 1989 by Topper Hermanson Boat in Fernandina
Beach, Florida, to a Bruce Roberts offshore cruising design. She is configured as an auxiliary cutter/sloop and was built
around the priorities that matter to experienced cruising sailors: structural strength, serviceability, substantial tankage,
manageable sail combinations, generous interior volume and access to the mechanical and electrical systems.
The February 2023 insurance survey valued Ravenwing at $81,000 in average condition while she was actively undergoing
restoration, with an estimated replacement cost of $600,000. Since that survey, the owner reports continued preservation
and improvement work, including Lexan-window resealing, toe-rail and localized steel welding, renewed shaft packing,
electrical-control improvements and additional cosmetic and systems work. The survey is therefore used as a detailed
equipment and construction baseline—not as a description of her current condition.
Data Sheet
HIN/IMO: TPR44001G989
Official Number: 955577
In Stock: Yes
LOA: 44' (13.41 Meters)
Type: Sail- Used
Year: 1989
Beam: 13' 8''
Draft Max: 5'
Draft Min: 5'
Cabins: 3
Sleeps: 8
Heads: 1
Fuel Type: Diesel
Hull Material: Steel
Hull Finish: Paint
Hull Shape: Monohull
Air Conditioning: Yes
Tower: No
Fuel Tank: 180 Gallons (681.37 Liters)
Designer: Bruce Roberts
Builder: Topper Herman
Multimedia
Engines
Engine 1
- Engine Make: Perkins
- Engine Model: 236
- Engine Year: 1989
- Engine Type: Inboard
- Drive Type: Direct
- Power HP: 85.00
- Power KW: 63.38
- Fuel Type: Diesel
- Engine Location: Middle
Full Details
Vessel Highlights
Vessel Highlights
Bruce Roberts 44 custom offshore cruising design
Custom welded-steel construction by Topper Hermanson Boat of Fernandina Beach, Florida
USCG documented vessel; Official Number 955577
Documented dimensions: 44.0 feet length, 13.8 feet breadth and 5.0 feet depth
20 gross tons / 16 net tons
Perkins 236 naturally aspirated four-cylinder diesel rated at 85 HP
Borg Warner mechanical transmission with 2:1 reduction
Cutter sail plan with mainsail, staysail, 130% genoa and Code 0 spinnaker
Profurl headsail furling system
Seven two-speed self-tailing winches: Lewmar #55, Harken #46.2 and Lewmar #43
Garmin 740s chartplotter with Garmin radar dome
Dual autopilot systems: Simrad AP26 and Wagner MP-320
Xantrex 2,000-watt inverter/charger
Nature Power wind generator with MPPT controller
Two 100-watt solar panels with Renogy controller
Sea Recovery watermaker rated by owner at approximately 5-6 gallons per hour
Aqua-Air 16,000 BTU reverse-cycle air conditioning
Approximately 180 gallons of diesel fuel in three stainless-steel tanks
Two heads; aft head includes a separate stand-up/sit-down shower
Dedicated port-side tool room/workshop
Large engine room with excellent access from multiple points
KR 8-foot 2-inch aluminum-bottom inflatable dinghy with Florida registration
Honda 2.3 HP outboard
Specifications
Specifications
Year: 1989
Vessel Name: Ravenwing
Designer: Bruce Roberts
Builder: Topper Hermanson Boat, Fernandina Beach, Florida
Build Date: July 1989
Type: Custom steel auxiliary cutter/sloop
Length Overall: 44 feet
Beam / Documented Breadth: 13.8 feet
Documented Depth: 5.0 feet
Hull Material: Welded steel
Deck Material: Steel plate with painted nonskid
Cabin Roof / Hardtop / Cockpit Superstructure: Aluminum
USCG Official Number: 955577
Gross Tonnage: 20
Net Tonnage: 16
Engine: Perkins 236 naturally aspirated four-cylinder diesel
Engine Rating: 85 HP
Transmission: Borg Warner mechanical, 2:1 ratio
Fuel Capacity: Approximately 180 gallons total
Hull, Structure & Exterior
Hull, Structure & Exterior
Welded-steel hull and welded-steel bottom plating
Steel plate deck with painted nonskid surface
Aluminum cabin roof, hardtop and cockpit structure
Reverse transom with steel sugar-scoop swim platform
Stainless-steel drop-down boarding ladder
Large watertight-style aft-cabin entrance hatch in the transom
Longitudinal internal framing using 1/4-inch x 3-inch steel bar welded into transverse frames
Additional welded framing in machinery, cabin-sole and foredeck areas
Steel compression post beneath the deck-stepped mast
Plywood bulkheads tabbed to wood blocks epoxied to the steel structure
Marelon seacocks with double-clamped hoses
Stainless-steel rub rail
Stainless-steel toe rail welded to the gunnels
Owner reports toe-rail and localized steel welding completed where required
Owner reports Lexan cabin windows removed/resealed to address water intrusion
Topsides described as structurally solid; preparation and cosmetic paint remain an opportunity for the next owner
Deck, Cockpit & Ground Tackle
Deck, Cockpit & Ground Tackle
Welded-steel dual-roller anchor platform
Below-deck anchor and chain locker accessed from the forward cabin
Stainless-steel deck pipe with secured cover
Maxwell Nilsson combination chain/rope windlass
Stainless-steel bow pulpit and stern rail
Stainless-steel stanchions
Double Dyneema lifelines
Secure deck hatches and forward escape hatch
Stainless-steel bow bollard
Horn cleats and fairleads
Teak cabin-top grab rails
Cowl ventilation
Magma rail-mounted propane grill
Ipe aft-deck arch supporting solar panels and antennas
Mid-cockpit arrangement
Welded U-shaped cockpit seating
Steel cockpit sole
Two large cockpit drains
Aluminum hardtop
Sliding wood companionway hatch and drop board
Cockpit bench storage
Freshwater transom washdown
Approximately 60-pound plow primary anchor
Approximately 45-pound aluminum fluke secondary anchor
Approximately 135-pound Navy storm anchor
Spars, Standing Rigging & Sail Handling
Spars, Standing Rigging & Sail Handling
White-painted aluminum deck-stepped mast
Double aluminum blade spreaders
Steel compression post
Aluminum boom
Line-and-block boom vang
Dyform stainless-steel performance standing rigging
Split backstay and baby stay
5/16-inch lower and intermediate shrouds
3/8-inch upper and lower shrouds
Staylock swageless terminals
Chromed-bronze open-barrel turnbuckles
Welded chainplates
Profurl foresail furler
Yacht-braid halyards
Aft-boom mainsheet with cabin-top traveler
Genoa tracks and cars on both side decks
Running rigging led aft to the cockpit
Cabin-top rope clutches and cam cleats
Doyle Stack Pack with lazy-jack lines
Adjustable aluminum whisker pole
Two Lewmar #55 two-speed self-tailing cockpit winches
Two Harken #46.2 two-speed self-tailing cockpit winches
Three Lewmar #43 two-speed self-tailing mast winches
Sail Inventory
Sail Inventory
Dacron mainsail with partial battens
Three reef points in the mainsail
Staysail
130% genoa
Code 0 spinnaker
Canvas mainsail cover / Doyle Stack Pack
Helm, Navigation & Communications
Helm, Navigation & Communications
Forward cockpit helm station
Wagner hydraulic steering
Stainless-spoke steering wheel
2-1/2-inch stainless-steel rudder stock
Emergency tiller
6-inch Wagner autopilot compass
Simrad AP26 autopilot
Wagner MP-320 autopilot system
Garmin 740s chartplotter
Garmin radar dome mounted on the forward mast
Garmin Echo 301c fishfinder/depth display
Garmin handheld GPS
Cobra DSC VHF radio
Uniden handheld VHF
SGC single-sideband radio
SSB backstay antenna
Handheld digital anemometer
Analog rudder-position indicator
Teleflex single-lever throttle and shift control
Analog engine tachometer, oil-pressure, temperature and voltage gauges
Functional high-water alarm
Xintex S2 propane-vapor detector
Battery-parallel emergency-start switch
Engine, Transmission & Running Gear
Engine, Transmission & Running Gear
Perkins 236 naturally aspirated four-cylinder diesel
85 HP rating
Freshwater / heat-exchanger cooling
Engine-mounted and 12-volt auxiliary fuel pumps
Dual Racor fuel-filter / water-separator arrangement
Two alternator regulators, including a backup regulator
Borg Warner mechanical transmission
2:1 gear ratio
1-1/2-inch stainless-steel propeller shaft
Bronze hex-nut stuffing box and packing gland
Owner reports shaft packing renewed approximately four years ago
Fiberglass water-lift muffler
Flexible wet-exhaust hose
Large engine room with access through the companionway steps and port/starboard doors
Engine room offers unusually good machinery, filter, shaft and system access for a 44-foot sailboat
Electrical, Batteries & Charging
Electrical, Batteries & Charging
12-volt DC system
30-amp / 120-volt AC shore-power system
One engine-start lead-acid battery
Four 6-volt lead-acid house/windlass batteries configured for 12 volts
Multiple rotary battery-selector switches
Engine-driven alternator charging
Xantrex charger/inverter with remote control
Xantrex model 81-2010-12, 2,000-watt / 110-volt output
Nature Power wind generator
MPPT wind-generation controller
Two 100-watt solar panels
Renogy solar controller
Main-cabin AC and DC distribution panels
Analog AC/DC amperage and voltage meters
Digital DC voltage meter
Reverse-polarity indicator
GFCI protection in galley, head and wet locations
Owner walkthrough showed additional labeled electrical panels and smart-control equipment
Tankage, Water & Plumbing
Tankage, Water & Plumbing
Three stainless-steel fuel tanks beneath the main cabin sole
Approximately 180 gallons total diesel capacity, per owner
Fuel manifold with ball-valve shutoffs
Algae-X fuel-treatment / filtration system
Two stainless-steel freshwater tanks beneath the cabin sole
12-volt pressure-water pump
Hot and cold pressure water
Freshwater and raw-water foot pumps at the galley
One approximately 10-gallon fiberglass holding tank
USCG Type III marine sanitation arrangement
Deck pump-out and overboard-discharge capability
Manual macerator / discharge pump
Camplux propane water heater as installed at survey
Two LPG cylinders: one aluminum and one FRP
Remote LPG solenoid shutoff
Xintex S2 gas detector and alarm
Sea Recovery desalination / watermaker system
Owner-stated watermaker output of approximately 5-6 gallons per hour
Accommodations & Interior Layout
Accommodations & Interior Layout
Traditional custom cruising interior
Main salon incorporates galley, dinette, additional seating and navigation station
Forward stateroom with V-berth
Forward head compartment
Aft master stateroom with island-style queen berth
Two separate companionways leading aft
Starboard aft companionway incorporates the aft head
Port aft companionway serves as a tool room / workshop
Two heads total
Aft head plumbed and functional at survey
Aft head with porcelain sink
Forward head with stainless-steel sink
Separate stand-up or sit-down shower in aft head
Teak folding dinette table converts the dinette to an additional berth
Bench seating with storage beneath
Navigation table with under-top storage, swivel seat and chart light
Hanging lockers and storage compartments
Full cloth-covered cushions
Opening portlights with screens
12-volt white and red cabin lighting
12-volt fans throughout cabin areas
Stainless-steel interior grab rails
Weems & Plath barometer
Small safe beneath main-cabin seating
Excellent direct access to the engine room and vessel systems
Galley
Galley
Starboard-side galley
Single deep stainless-steel sink
Pressurized hot and cold water
Freshwater foot pump
Raw-water foot pump
Force 10 three-burner LPG stove
Force 10 oven
Two Aspenora portable 12/110-volt convertible refrigerator/freezers
Galley storage
Dedicated galley lighting
Climate Control & Entertainment
Climate Control & Entertainment
Aqua-Air 120-volt reverse-cycle air conditioning
16,000 BTU main-cabin system
Digital temperature control
Heating and cooling operation verified during the 2023 survey
Portable Toshiba 110-volt air conditioner / dehumidifier
West Marine AM/FM/CD stereo
Cabin and cockpit speakers
Seiki 18-inch LED television / computer monitor
Safety Equipment
Safety Equipment
Four Type I USCG life jackets
Two Type V inflatable life jackets
USCG ring buoy with tether
Visual-distress signals
Handheld air horn
Ship's bell
Four Size I dry-chemical fire extinguishers
Two Size II dry-chemical fire extinguishers
Two electric bilge pumps rated approximately 1,500 and 2,500 GPH
Independent float switches
Functional high-water alarm
Whale manual bilge pump
First-aid kit
Smoke detector
Handheld 12-volt searchlight
Navigation lights
Inland Navigation Rules book
Dinghy, Tender & Included Cruising Gear
Dinghy, Tender & Included Cruising Gear
KR Boat inflatable tender
Aluminum hard bottom
8 feet 2 inches length
Florida registration FL7186RU
Stored inverted on the side deck
Honda BF2.3D 2.3 HP outboard
Integral outboard fuel tank
Three-blade propeller
Multiple dock lines
Assorted fenders
Binoculars
Boat hook
Cleaning supplies
Spare system and engine parts
Spare propeller
Extensive onboard tools
Owner reports separate Florida title/documentation for the dinghy
Owner Improvements Since the 2023 Survey
Owner Improvements Since the 2023 Survey
The following items are based on the owner & subsequent reports and walkthrough information. They should be confirmed
against receipts and inspected before publication, but they are important because the survey described Ravenwing while
active restoration was underway.
Lexan cabin windows removed and resealed
Toe-rail and localized steel welding completed where required
Shaft packing renewed approximately four years ago
Electrical-panel and smart-control improvements
Additional engine-room organization and system access improvements
Continued restoration of the aft master and interior living spaces
Ongoing exterior preservation and cosmetic work
Original construction photographs and ownership records reportedly available
Condition & Broker & Observations
Condition & Broker & Observations
Ravenwing should be presented honestly as a substantial custom steel cruising yacht—not as a cosmetically perfect
production sailboat. Her strongest selling points are the Bruce Roberts design pedigree, documented local build, welded-
steel structure, serious cutter sail plan, robust cruising systems, generous fuel capacity, large engine room and practical
two-stateroom liveaboard layout.
The 2023 insurance survey rated the vessel in average condition while restoration was in progress
The same survey estimated fair market value at $81,000 and replacement cost at $600,000
The owner reports multiple survey-era deficiencies and preservation items have since been addressed
Exterior paint and cosmetic finishing remain a visible opportunity for the next owner
A current condition-and-value survey and ultrasonic steel-thickness inspection are recommended for any buyer
Machinery hours were not shown on a meter during the 2023 survey and should not be represented without owner
documentation
Electronic equipment should be demonstrated and operating status confirmed during showing or survey
This vessel will appeal most strongly to experienced cruising sailors, steel-boat buyers and liveaboard owners who value
access, strength and long-range systems
Showing & Contact
Showing & Contact
Showings by appointment through Redmond Boats & Yachts
Larry Redmond
Phone: 904-206-0719
Website: RedmondYachts.com
Please allow adequate time to inspect the engine room, steel structure, electrical systems, rig, records and cruising inventory
Brokerage Disclaimer
The Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information
nor warrant the condition of the vessel. A buyer should instruct agents and surveyors to investigate all details the buyer
desires validated. Equipment and operating status are subject to owner confirmation and buyer inspection. This vessel is
offered subject to prior sale, price change or withdrawal without notice.
Listing MLS by Yachtr.com
Contact Us
For more information about this yacht please contact Larry Redmond.
We look forward to working with you!
Redmond Boats & Yachts
Fernandina Beach FL 32034 USA
Email: info@redmondyachts.com
Website: https://redmondyachts.com
With 30+ years in the boating and yacht sales business, our team at Redmond Boats & Yachts combine knowledge, passion, and experience when it comes to serving our customers. We are your “one-stop-shop” as you search for buying a new boat of your dreams and we will walk with you through the process step by step to get you and your family on the water as soon as possible.
Larry Redmond
Yacht Broker
Fernandina Beach FL 32034 USA
Cell: 1-904-206-0719
Email: redmondyachts@gmail.com
Short Version !!
Boat and Yacht Business since 1986. Moved to Florida in 1991. Took a Job in Jacksonville Fl with one of the largest Dealers selling New Boat Brands From Boston Whaler to Chaparral, Mako, Bass tracker, Ranger Bass and Offshore. I was Introduced To Boston Whaler in 1992 and was taken under there wing and invited to work major Boat Shows in Miami , Fort Lauderdale and Atlanta. A ton Of Brunswick training came from this with Whaler and Sea Ray, Over the Years. Even being on the Dealer Design Team for years for Whaler and Others. All of this is was for Product Knowledge ,Customer service including after the sale. Teaching People about Boating what and Why. Most of the training Disappeared in the early 2000;s and Hope it will come Back. Redmond Boats was Formed in the early 2000's after leaving Marina Max as a Store Manager .
I received my Florida Broker License in 2006 and Became a Employing Broker Soon after . I was the Parker and Tidewater dealer (New) up to 2018 were I began only brokerage full Time. I list and sell my Customers Vessels a little different then Most were the results on Both Sides seem to go very Well and I gain another customer during the process . Its a people business. Your Buyer and seller needs good help
I grew up in Louisiana where my love and expertise for boats and yachts began. Louisiana is a sportsman’s paradise and the average person has somewhere near four boats. As a child, all we really had to do was boat and fish. My first boat was a rubber raft and at five years old I would go and shoot snakes down in the bayou. I loved being on the water. The first boat deal I ever negotiated was around the 8th grade. It has been history ever since. I was on the way home from doing some work in West Virginia after a Disaster and I stopped to visit my uncle in Alabama. I ended up staying five years. During my time there I Interviewed for a Boat Rigging Job.
I was accepted but was Quickly Moved to the Front Office in Learning the Sales Side as well as the Service writer During these years (Late 1980's).I learned a lot on The Service Side as well as the New Boat Side. This was the Biggest sales in units in Retail Boating. Unfortunately the industry Crashed in 1989 With Interest Rates and Other issues. I ended up in Florida in 1991 and was able to connect with a gentleman who got me set up with my first job dealing boats. In the early 2000s, because of past relationships and connections within the boating community, people began to seek me out to help them buy or sell their boats. My business grew from 100% referrals. For me, it’s all about putting a face to a boat and a boat to an experience. I enjoy meeting people one on one and helping them find the boat of their dreams.
